1. Remote control layout
2. Inserting Batteries
- Slide the battery housing cover downwards to remove.
- Insert 2 x AAA batteries observing the correct polarity.
- Refit the battery housing cover.
2.1 Battery Information
- Do not mix different types of battery or old and new
batteries. - Do not use rechargeable batteries with the remote
control. Do not attempt to recharge the batteries. - Remove the batteries from the remote control if you
are not going to use it for several weeks, to avoid the
risk of leakage. - Immediately remove any leaking batteries. Take care
when handling leaking batteries as they may cause
burns to the skin or eyes, or other physical injuries. - Please respect your environment and any local
regulations and dispose of old batteries in a
responsible manner.
3. Operation
All buttons transmit commands for the STB, however the exact button function will depend on your service provider. When pressing a remote control button, point the remote control towards the front of the STB to ensure correct operation. Do not cover the infra-red (IR) window at the front of the STB.
When a button on the remote control is pressed, either the STB standby button or the TV standby button (if a TV brand has been entered) will flash. The button which flashes will depend on which product is being controlled by the remote control.
If a button is pressed for more than 30 seconds the
remote control will stop transmitting commands to
preserve battery life.
4. TV control setup
4.1 Brand Search
The remote control can be programmed to operate certain
functions of your TV set. To do this, follow the instructions below.
*Please note: in case of a mistake, you can exit a process at any point by pressing and holding the TEXT/SHIFT button at the same time as the STOP button. The remote control will revert back to normal operation and no TV brand code will be stored.
- Note the brand of your TV set.
- Find the 4-digit brand code for your TV set by referring to the
brand code tables on the Amino resources page.- Make a note of the brand code.
- If the remote control cannot find the TV brand, the TV standby button will flash rapidly, and the remote control will revert to normal operation. No TV brand code will be stored.
- Make sure your TV set is turned on. (The STB does not need to be turned on to perform this programming feature).
- Press and hold the 1 and 3 buttons simultaneously for approximately 3 seconds until the TV standby button remains lit, then release both buttons.
- Enter the 4-digit brand code for your TV set. On each digit entry the TV standby button will flash. When you enter the 4th digit the TV standby button will flash then remain lit.
- Point the remote control at your TV set, then press and hold down the TV standby button or the Mute button on the remote control.
- The TV set will either turn off or display the MUTE symbol on screen (this may take a few minutes). When this happens, release either the TV standby or the Mute button.
- Press and hold the TEXT/SHIFT button and at the same time press the STOP button to finish setting up the TV control mode. The TV standby button will go out. The TV control function is now programmed into the remote control.
The following buttons will now operate the TV set:
- TV standby
- AV source select
- Volume Up
- Volume Down
- Mute
If any of these buttons do not operate the TV set, then a KEY FIX operation can be performed (see below).
4.1.1 Key fix
If not all the buttons listed under TV shift functionality operate the TV set, then a KEY FIX operation can be performed as follows:
- Press and hold the 1 and 9 buttons simultaneously for approximately 3 seconds until the TV standby button is lit.
- Try all the above-mentionedTV buttons.
- If the TV does not respond to a button, then hold that buttondown permanently. The remote control will now step through alternative settings. When the TV responds correctly, release the button.
- Repeat the procedure for other buttons if necessary.
- When you have finished, press TEXT/SHIFT and STOP
If you change your TV set to a different brand and the remote control requires re-programming, repeat this brand search procedure with your new TV set.
4.2 Auto Search
If the TV brand cannot be found by the previous Brand Search method, then the Auto Search method be used instead.
*Please note: this process may take several minutes to find your TV code. Make sure your TV set is turned on. The STB does not need to be turned on to perform this programming feature.
- On the remote control, press and hold the 1 and 3 buttons simultaneously for approximately 3 seconds until the TV standby button remains lit, then release both buttons.
- Point the remote control at your TV set, then press and hold down the TV standby button or the Mute button.
- When the TV either turns off or brings up the MUTE symbol on screen, release either the TV standby button or the Mute button. This may take a few minutes to happen.
- Press and hold the TEXT/SHIFT button and at the same time press the STOP button to finish setting up the TV control mode. The TV standby button will go out. The TV control function is now programmed into the remote control.
If the remote control cannot find the TV brand, the TV standby button will flash rapidly, and the remote control will revert to normal operation. No TV brand code will be stored. If Auto Search cannot set up operation of the TV set, then the remote is unable to control that TV set.
When a TV brand has been programmed into the remote control using either of the previous methods, the following additional buttons can also control the TV set. These can be accessed by pressing and holding the TEXT/SHIFT button and at the same time pressing:
- Digit buttons 0=9, Left, Right, Up, Down, OK, Channel Up, Channel Down, the 4 colour keys.
*Please note: operation of these buttons is not guaranteed to control the functions of your TV set.
5. Removing TV Functionality
To reset the remote control and erase the TV functionality:
- Press and hold the 1 and 6 buttons simultaneously for approximately 3 seconds until the TV standby button is lit.
- Enter the key sequence 9 9 6. The TV settings will be deleted from the remote control.
Comments
0 comments
Please sign in to leave a comment.